Solar PV MicroFIT
	Top-Quality CSUN Solar Cells For its solar cells, WSE has entered into a partnership with CSUN, one of largest and best PV cell manufacturers in the world. By using CSUN’s new SE (Selective Emitter) cells with up to 19% efficiency, WSE is able to deliver significantly more Watts per surface area, an invaluable advantage in any solar project.
	SunEdge™ Mounting Frame WSE Panels uses two different types of frames for its solar panels: industry-standard frames and custom SunEdge™ frames. The patented SunEdge™ frame integrates directly into WSE’s SunRail™ mounting system for fast, solid and easy installations.

	What is a StructuralPV™ Module? Technology that make solar installations easier and less costly. Still today, most commercial and industrial installations are done using the same methods as for smaller residential systems. The concept of StructuralPV™ is to bring some of the advancements in commercial construction to the solar industry. How it works. StructuralPV™ modules are made of several crystalline PV panels pre-assembled in factory, where they are reliably mounted into a solid structure, connected and tested assembled. The StructuralPV™ modules are then shipped directly to the installation site, where they are installed with modern construction methods using the SunRail™ mounting system, which dramatically increases speed, reduces labor costs, maximizes power output and results in a very solid and reliable system. StructuralPV™ Features • Uses exactly the same aluminum extrusion as the SunRail™ mounting system. • Mono-crystalline PV panels pre-assembled and tested in factory. • Delivered to the project site, ready to install. • Integrates directly into SunRail™ mounting system. • Sizes vary -- up to 4 panels wide x 3 panels high. • Output per StructuralPV™ up to 3.6 kW (12 x 300W panels). • Up to 600 Volts of matched PV panels. Benefits of StructuralPV™ • 3% more power output: factory pre-assembly avoids panel mismatch. • Enables up to 5X more installations per year with same team of workers. • Installations are much faster. • Installed with a crane, resulting in significantly lower labor costs. • Once assembled, system is very solidly built and weather-resistant. • Tested assembled, assuring maximum reliability.

	The SunRail™ Concept A practical, low-cost mounting solution that maximizes performance and reliability on any roof or land. The SunRail™ is a patented aluminum extrusion that, combined with the patented SunJoint™ clamps, can be cut and assembled into any type of solar installation, of any size. Aluminum Extrusion The SunRail™ extrusion is used as the complete structure for WSE’s mounting system as well as WSE’s StructuralPV™ pre-assembled modules. The unique aluminum extrusion is delivered to the project site in lengths of up to 24 feet, where it can be conveniently cut by the installer to fit any system size. Pre-cut beams are also available for certain standard setups. The SunRail™ extrusion provides exceptional strength for even the most heavy-duty projects, at a very competitive cost. SunJoint™ Clamps The SunJoint™ clamps are a small set of folded metal pieces with bolts and lock nuts that are used to rapidly and conveniently assemble the SunRail™ mounting system. Some of the SunJoint™ clamps robustly connect SunRail™ extrusions together into a mounting structure, while others are used to tightly attach PV panels, either with a standard frame or a SunEdge™ frame, to the mounting system. The clamps only require a wrench and can be tightened with one hand to build a solid mounting structure for virtually any project type or size. The SunRail™ Advantage • Fast, easy and convenient installation. • Low-cost: simple design and few parts. • Fits virtually all installations and PV panels. • Completely flexible: installer cuts to desired size. • Very solid and sturdy, even for heavy-duty applications. • Comes with a 25-year limited product warranty. • Made in Ontario.
Mounting type One single extrusion is used for the entire assembly, along with SunJoint™ clamps. Roofing material Suitable for most types of roofing. Rail height adjustability As desired Rail length Up to 24 feet Rail Material 6005 T5 and 6063 T5 Clamp material 6005 T5 aluminum with stainless steel bolt and cramp. Finish Mill finish or anodised to the desired color on demand. Module type Compatible with most major manufacturers and models. Maximum array size Any size Tilt range 5° - 75° degrees Wind load 90mph Snow load 50 PSF Warranty 25 years

	Commercial Rooftop System Why High-Profile? In climates such as Canada, snow is a major concern. Only a little snow obstruction can incapacitate 100% of a panel installed vertically and 33% of a panel installed horizontally. Low-Profile also available. In addition to the High-Profile, or above-ground, system shown above, the SunRail™ can also be assembled Low-Profile such as shown in A below. No ballists required. The SunRail™ is so sturdy that it has the same stability as a ballisted system, yet it requires no additional ballists. (varies based on application) Absolute flexibility. Because the SunRail™ consists simply of WSE’s patented aluminum extrusion, engineers and contractors can design for themselves the mounting system that best suits every project’s needs.
Installation steps (follow images): 1. Lay down SunRail™ tracks. • Simply lay on ground. • No screws or ballasts required. 2. Attach vertical supports. • One for the front, one for the back. • SunJoint™ attaches quickly and solidly. 3. Place bottom SunJoint™ clamps. • Goes on the front, shorter legs. • Clamps compatible with all panel frames. • Ideal for StructuralPV™ and SunEdge™. 4. Lower module onto clamps. • With crane or by hand (varies). 5. Lean module backwards, attach top clamps. • Module should fall right on back legs. • Clamps compatible with all panel frames. • That’s it!

	Residential Rooftop System Few parts, maximum strength. The SunRail™ allows for a very strong solar array with minimal parts, thus lower costs. There are only lateral supports, and one track holds two panels. Fast installations. The SunRail™ tracks are easy to install and the SunJoint™ clamps are quick to attach, resulting in fast installations that minimize costs. Roof penetration is flexible. The beam attachments are placed directly on top of roof beams, which allows many options for contractors. Layout does not depend on roof. Because the SunRail™ can be designed to optimally fit any roof with beam attachments and then have transversal rails on top, the placement and size of solar panels become independant of the way the roof is built.
Installation steps (follow images): 1. Install beam attachments. • Place directly on beam. • Method of screwing/sealing is flexible. 2. Attach lateral supports. • Connect to beam attachments. • Provide solid support for panels. 3. Place bottom SunJoint™ clamps. • Start with bottom row only. • Single-sided and double sided clamps. • Clamps compatible with all panel frames. 4. Place first row of panels. • Panels are held steadily in place. 5. Attach top clamps, install next row. • Use double-sided clamps if more rows. • Clamps compatible with all panels frames. • Repeat steps 4 and 5 until finished. • That’s it!

WSE 72M PV PANEL
CHARACTERISTICS Type WSE 300-72M WSE 295-72M WSE 290-72M Peak Power 300W 295W 290W Voc [V] 44.8 44.6 44.5 Isc [A] 8.8 8.73 8.68 Vmp [V] 36.1 35.9 35.8 Imp [A] 8.32 8.22 8.11 All parameters of electrical characteristics are tested under STC: 1000 W/m2, AM 1.5, 25°C.
OTHER PARAMETERS Max System Voltage 1000V (IEC) Temperature Coefficient of Voltage -0.36%/K Temperature Coefficient of Current 0.03%/K Temperature Coefficient of Power -0.52%/K NOCT 45°C Fuse Current 15A Mechanical Load Not less than 2400Pa Basic Structure Front Side Low-iron tempered glass Back Side Color custom composite film Frame

WSE 60M PV PANEL

CHARACTERISTICS Type WSE 250-60M WSE 245-60M WSE 240-60M Peak Power 250W 245W 240W Voc [V] 37.3 37.2 37 Isc [A] 8.78 8.69 8.62 Vmp [V] 30.1 30 29.8 Imp [A] 8.31 8.17 8.06 All parameters of electrical characteristics are tested under STC: 1000 W/m2, AM 1.5, 25°C.

OTHER PARAMETERS Max System Voltage 1000V (IEC) Temperature Coefficient of Voltage -0.36%/K Temperature Coefficient of Current 0.03%/K Temperature Coefficient of Power -0.52%/K NOCT 45°C Fuse Current 15A Mechanical Load Not less than 2400Pa Basic Structure Front Side Low-iron tempered glass Back Side Color custom composite film Frame Aluminum alloy

Ready to order or have some questions?

Simply pickup the phone and call 1 306 244 8808

(Barry  ext 242 ) (  Brayden ext 239) (Lee ext 232)

Click here to Contact WSE

Become A Dealer

Become involved with a dynamic company and dynamic industry that will see exponential growth and opportunities over the next 20 years. The key is to get in NOW before it is too late.

  Talk to our President Larry Fedoruk 1 306 244 8808 or Email

Information about become a dealer click here

WSE Technologies
303 - 47Str. E
Saskatoon
Saskatchewan
Canada
S7K 5H2

Ph: 1 306 244 8808
Fax: 1 306 244-9970

We accept Visa and Master card.

WSE twitter